Sensor Accessories

Pocket Wrench With 5/64” Allen Wrench For Branch Test Port on Pneumatic Thermostats and Locking Cover Screws and 0.048” 6-spline Wrench

Snap-in “labor-saving” fitting for mounting 2 x 2 in. thermostats, humidistats, and transmitters on drywall having at least 3-½ in. studs.

1/16 in. and ¼ in. hex head thermostat calibration and coverscrew wrench. (Also adjusts 2341 Series Receiver-Controllers.)

AA Series duct static pickup probe, 8”, dry pressure

Wire Guard With Steel Base Plate, 4-¼”H x 1-⅝”W x 1-⅝”D

Dial Stop Kit

Gray cover with Barber-Colman logo dial

Pilot Restrictor Kit (All Relay Type Except -600)

1.0 scfh In-Line Restrictor.

Gasket for TAC Pneumodular Control System

Gray cover with Barber-Colman logo dial

Restrictor for copper fitting

Adaptor Kit

Factory Authorized Parts™ - HH79HZ004 - THERMISTOR ASSEMBLY

Replacement Humidity Element for Veris Sensors, 2% Accuracy

Base For Field Mounting Pneumodular Receiver-Controller, Plus Two 2” Receiver Gauges and Two 1-½” Pressure Gauges, Direct Acting

Klipet Capillary Clip

AA Series room static pressure pickup

Thermostat conversion kit, white.

RH SENSOR 5% REPLACE ELEMENT

Replacement Humidity Element, 1% Accuracy, NIST

RH SENSOR 2% REPLACE ELEMENT

AA Series duct static pickup probe, 4”, dry pressure

Dial Stop Pins, to Limit the High or Low Setting of Room Thermostats (100 Per Pack)

Static Pressure Pickup Port: Wall mounted, Stainless steel wall plate with sinter vent, For use with Veris Px series sensors

Setpoint Scale TK-17xx, 18xx, 55-85F/C

LINKAGE KIT

Squeeze Bulb Pump With Valve For Testing pneumatic Controls And Actuators.

Electrical Contact Assembly for TAC Pneumodular Control System

Setpoint Knob Kit Fahrenheit,TK-1001 thru TK-1601

Air Velocity Averaging Pitot Tube 6 in

Air Velocity Averaging Pitot Tube 8 in

Air Velocity Averaging Pitot Tube 10 in

Pneumatic Capacitor

STP Series pocket STP, 100 mm/3.94 in., brass

Packing Wrench For VB-121, VB-131, VB-151, VB-314, VB-324, VB-334, VB-354 Valves

Remote Sample Pick-Up Kit: For Use With Veris CDR Series Products

Gauge tap adaptor for T15 or T16 only. One end accepts ⅛ in. MPT gauge, other end screws into thermostat body.

Lock Cover Screw Kit, to Prevent Unauthorized Tampering of Dial Setting or Internal Mechanism

Tee Restrictor, .0075”, For ¼” Plastic Tubing

1.0 scfh Restrictor Tee for Use with One-Pipe Thermostats or Transmitters (¼ in. polythylene or polyurethane tubing). Color: red.

Tubing Connectors Quantity Package (50) for TAC Pneumodular Control System

Gray cover with Barber-Colman logo dial

Socket Assembly (includes one 22-130) for TAC Pneumodular Control System

Gray cover with Barber-Colman logo dial

Adaptor, brass, for mounting T150 Immersion Transmitter in Barber-Colman AT-201 or AT-203 well.

Mounting Plate For Mounting Any Two Single Function Room Controllers, 6-14”H x 6-¼”W x ¼”D

Resistor Kit, Converts and Interfaces a 4 to 20 mAdc External Signal to 1 to 11 Vdc Signal, 250 Ohm, +/-0.1% Tolerance, ½ Watt, T (6 Pack)

Mounting Screw for TAC Pneumodular Control System

Plug Strip for TAC Pneumodular Control System

Mounting Base, Auxiliary, Single, 5-7/16”H x 3-⅞”W x ⅜”D

Voltage Divider

Sealing Plug for TAC Pneumodular Control System

3/16 in. tygothane tubing assembly, with spring, two eyelets, and two barbed fittings for ¼ in. plastic tubing.

Aspirator Kit

Check Valve for TAC Pneumodular Control System

Needle and Adaptor For Use With ¼” Plastic Tubing and AL-88 and AL-89 Test Fittings

Check valve tee. Mounts on upper end of 22-120 socket, permits connection to field-mounted devices.

Gray cover with Barber-Colman logo dial