Sensor Accessories

Pocket Wrench With 5/64” Allen Wrench For Branch Test Port on Pneumatic Thermostats and Locking Cover Screws and 0.048” 6-spline Wrench

TAC Pneumodular tubing - 100 Ft. Roll

Snap-in “labor-saving” fitting for mounting 2 x 2 in. thermostats, humidistats, and transmitters on drywall having at least 3-½ in. studs.

Receiver-Controller, Reverse-Acting

Receiver Controller, Universal Replacement Single or Dual Input With Remote Set Point Adjustment, Cover Included

AA1 Series bypass valve assembly

AA Series duct static pickup probe, 8”, dry pressure

1/16 in. and ¼ in. hex head thermostat calibration and coverscrew wrench. (Also adjusts 2341 Series Receiver-Controllers.)

Wire Guard With Steel Base Plate, 4-¼”H x 1-⅝”W x 1-⅝”D

STP Series pocket STP, 100 mm/3.94 in., brass

Receiver-Controller, Reverse-Acting, pre-mounted on base for field use

Packing Wrench For VB-121, VB-131, VB-151, VB-314, VB-324, VB-334, VB-354 Valves

Dial Stop Kit

Gray cover with Barber-Colman logo dial

Pilot Restrictor Kit (All Relay Type Except -600)

1.0 scfh In-Line Restrictor.

Sub-Base, Single Thermostat Selector Switch, One DP4T, One DPDT, For Use With All Single Electric Room Thermostats Except TC-114 and TA-121

Gasket for TAC Pneumodular Control System

Gray cover with Barber-Colman logo dial

Restrictor for copper fitting

Wire Guard With Steel Base Plate, 6-½”H x 6-⅝”W x 3-¼”D

Adaptor Kit

Gauge tap adaptor for T15 or T16 only. One end accepts ⅛ in. MPT gauge, other end screws into thermostat body.

Lock Cover Screw Kit, to Prevent Unauthorized Tampering of Dial Setting or Internal Mechanism

Factory Authorized Parts™ - HH79HZ004 - THERMISTOR ASSEMBLY

Tee Restrictor, .0075”, For ¼” Plastic Tubing

1.0 scfh Restrictor Tee for Use with One-Pipe Thermostats or Transmitters (¼ in. polythylene or polyurethane tubing). Color: red.

BULB ASSEMBLY

Gaskets Quantity Package (25) for TAC Pneumodular Control System

Aluminum Bulb Shield, Outdoor, 2”H x 11-¾”W x 1-⅛”D

Replacement Humidity Element for Veris Sensors, 2% Accuracy

Gray cover with Barber-Colman logo dial

Base For Field Mounting Pneumodular Receiver-Controller, Plus Two 2” Receiver Gauges and Two 1-½” Pressure Gauges, Direct Acting

Paralleling Relay: Solid Start, Actuator or Panel Mount

Klipet Capillary Clip

Sensing Cable, 25 ft

Conversion Kit, Pneumatic, Wall Thermostat Mounting

Socket Assembly, Includes 1 MCS-PS, 1 MCS-G, 4 MCS-SCREW, 15 MCS-PLUG

Spring: 3-8 MK-7100-0-0-1

Gray cover with Barber-Colman logo dial

Tubing Connectors Quantity Package (50) for TAC Pneumodular Control System

Gray cover with Barber-Colman logo dial

Socket Assembly (includes one 22-130) for TAC Pneumodular Control System

Gray cover with Barber-Colman logo dial

Adaptor, brass, for mounting T150 Immersion Transmitter in Barber-Colman AT-201 or AT-203 well.

Mounting Plate For Mounting Any Two Single Function Room Controllers, 6-14”H x 6-¼”W x ¼”D

Resistor Kit, Converts and Interfaces a 4 to 20 mAdc External Signal to 1 to 11 Vdc Signal, 250 Ohm, +/-0.1% Tolerance, ½ Watt, T (6 Pack)

Mounting Base, Auxiliary, Single, 5-7/16”H x 3-⅞”W x ⅜”D

CALIBRATION KIT for Veris CO2 Sensors

Plug Strip for TAC Pneumodular Control System

Voltage Divider

Thermostat conversion kit, white.

3/16 in. tygothane tubing assembly, with spring, two eyelets, and two barbed fittings for ¼ in. plastic tubing.

AA Series room static pressure pickup

Aspirator Kit

Mounting Screw for TAC Pneumodular Control System

Dial Stop Pins, to Limit the High or Low Setting of Room Thermostats (100 Per Pack)

Sealing Plug for TAC Pneumodular Control System

Needle and Adaptor For Use With ¼” Plastic Tubing and AL-88 and AL-89 Test Fittings

Check Valve for TAC Pneumodular Control System